The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube

Yanfeng Fan, Ibrahim Hassan

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50% and 20% area ratios. The experimental measurement is carried out at mass fluxes ranging from 160 - 870 kg/m 2s and heat fluxes varying from 6 - 170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.

Original languageEnglish
Title of host publicationASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013
Volume1
DOIs
Publication statusPublished - 2013
Externally publishedYes
EventASME 2013 Heat Transfer Summer Conference, HT 2013 Collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology - Minneapolis, MN, United States
Duration: 14 Jul 201319 Jul 2013

Other

OtherASME 2013 Heat Transfer Summer Conference, HT 2013 Collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology
CountryUnited States
CityMinneapolis, MN
Period14/7/1319/7/13

Fingerprint

Orifices
Boiling liquids
Heat flux
Heat transfer
Heat transfer coefficients
Mass transfer
Stainless Steel
Stainless steel
Heating
Fluids

ASJC Scopus subject areas

  • Fluid Flow and Transfer Processes

Cite this

Fan, Y., & Hassan, I. (2013). The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube. In ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013 (Vol. 1). [V001T03A016] https://doi.org/10.1115/HT2013-17284

The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube. / Fan, Yanfeng; Hassan, Ibrahim.

ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013. Vol. 1 2013. V001T03A016.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Fan, Y & Hassan, I 2013, The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube. in ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013. vol. 1, V001T03A016, ASME 2013 Heat Transfer Summer Conference, HT 2013 Collocated with the ASME 2013 7th International Conference on Energy Sustainability and the ASME 2013 11th International Conference on Fuel Cell Science, Engineering and Technology, Minneapolis, MN, United States, 14/7/13. https://doi.org/10.1115/HT2013-17284
Fan Y, Hassan I. The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube. In ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013. Vol. 1. 2013. V001T03A016 https://doi.org/10.1115/HT2013-17284
Fan, Yanfeng ; Hassan, Ibrahim. / The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube. ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013. Vol. 1 2013.
@inproceedings{0fe6841725ad4a88a11d558eb3d85813,
title = "The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube",
abstract = "Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50{\%} and 20{\%} area ratios. The experimental measurement is carried out at mass fluxes ranging from 160 - 870 kg/m 2s and heat fluxes varying from 6 - 170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.",
author = "Yanfeng Fan and Ibrahim Hassan",
year = "2013",
doi = "10.1115/HT2013-17284",
language = "English",
isbn = "9780791855478",
volume = "1",
booktitle = "ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013",

}

TY - GEN

T1 - The effect of inlet orifice on critical heat flux and flow boiling heat transfer in single horizontal microtube

AU - Fan, Yanfeng

AU - Hassan, Ibrahim

PY - 2013

Y1 - 2013

N2 - Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50% and 20% area ratios. The experimental measurement is carried out at mass fluxes ranging from 160 - 870 kg/m 2s and heat fluxes varying from 6 - 170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.

AB - Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50% and 20% area ratios. The experimental measurement is carried out at mass fluxes ranging from 160 - 870 kg/m 2s and heat fluxes varying from 6 - 170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.

UR - http://www.scopus.com/inward/record.url?scp=84892985467&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84892985467&partnerID=8YFLogxK

U2 - 10.1115/HT2013-17284

DO - 10.1115/HT2013-17284

M3 - Conference contribution

AN - SCOPUS:84892985467

SN - 9780791855478

VL - 1

BT - ASME 2013 Heat Transfer Summer Conf. Collocated with the ASME 2013 7th Int. Conf. on Energy Sustainability and the ASME 2013 11th Int. Conf. on Fuel Cell Science, Engineering and Technology, HT 2013

ER -