Simulating eddy current sensors in blade tip timing application

Modeling and experimental validation

Nidhal Jamia, Michael I. Friswell, Sami El-Borgi, Prakash Rajendran

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

In gas turbines, the blade vibration caused by aerodynamic excitation or by self-excited vibration and flutter leads to high cycle fatigue that represents the main cause of damage in turbomachinery. Turbine operators have resorted to assess the blade vibrations using non-contact systems. One of the well-known non-contact methods is Blade Tip Timing (BTT). BTT is based on monitoring the time history of the passing of each blade tip by stationary sensors mounted in a casing around the blades. The BTT method evaluates the blade time of arrival (ToA) in order to estimate the vibration. To perform the BTT technique, optical sensors were widely used by industry due to their high accuracy and performance under high temperatures, but the main drawback of these systems is their low tolerance to the presence of contaminants. To mitigate this downside, Eddy Current Sensors (ECS) are a good alternative for health monitoring application in gas turbines due to their immunity to contaminants and debris. This type of sensor was used by many researches, predominantly on the experimental side. The focus was to extract response frequencies and therefore the accuracy of the timing measurement was ignored due to the lack of modeling. This paper fills the gap between experiments and modeling by simulating a BTT application where detailed finite element modeling of active and passive ECS outputs was performed. A test rig composed of a bladed disk with 12 blades clamped to a rotating shaft was designed and manufactured in order to validate the proposed models with experimental measurements. Finally, a comparison between these different types of sensor output is presented to show the effect of the blade tip clearance and rotational speed on the accuracy of the BTT measurement.

Original languageEnglish
Title of host publicationMechanics of Solids, Structures, and Fluids
PublisherAmerican Society of Mechanical Engineers (ASME)
Volume9
ISBN (Electronic)9780791852149
DOIs
Publication statusPublished - 1 Jan 2018
EventASME 2018 International Mechanical Engineering Congress and Exposition, IMECE 2018 - Pittsburgh, United States
Duration: 9 Nov 201815 Nov 2018

Other

OtherASME 2018 International Mechanical Engineering Congress and Exposition, IMECE 2018
CountryUnited States
CityPittsburgh
Period9/11/1815/11/18

Fingerprint

Eddy currents
Sensors
Turbomachine blades
Gas turbines
Impurities
Flutter (aerodynamics)
Turbomachinery
Monitoring
Optical sensors
Debris
Frequency response
Aerodynamics
Turbines
Health
Fatigue of materials
Industry
Experiments
Temperature

ASJC Scopus subject areas

  • Mechanical Engineering

Cite this

Jamia, N., Friswell, M. I., El-Borgi, S., & Rajendran, P. (2018). Simulating eddy current sensors in blade tip timing application: Modeling and experimental validation. In Mechanics of Solids, Structures, and Fluids (Vol. 9). American Society of Mechanical Engineers (ASME). https://doi.org/10.1115/IMECE2018-87414

Simulating eddy current sensors in blade tip timing application : Modeling and experimental validation. / Jamia, Nidhal; Friswell, Michael I.; El-Borgi, Sami; Rajendran, Prakash.

Mechanics of Solids, Structures, and Fluids. Vol. 9 American Society of Mechanical Engineers (ASME), 2018.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Jamia, N, Friswell, MI, El-Borgi, S & Rajendran, P 2018, Simulating eddy current sensors in blade tip timing application: Modeling and experimental validation. in Mechanics of Solids, Structures, and Fluids. vol. 9, American Society of Mechanical Engineers (ASME), ASME 2018 International Mechanical Engineering Congress and Exposition, IMECE 2018, Pittsburgh, United States, 9/11/18. https://doi.org/10.1115/IMECE2018-87414
Jamia N, Friswell MI, El-Borgi S, Rajendran P. Simulating eddy current sensors in blade tip timing application: Modeling and experimental validation. In Mechanics of Solids, Structures, and Fluids. Vol. 9. American Society of Mechanical Engineers (ASME). 2018 https://doi.org/10.1115/IMECE2018-87414
Jamia, Nidhal ; Friswell, Michael I. ; El-Borgi, Sami ; Rajendran, Prakash. / Simulating eddy current sensors in blade tip timing application : Modeling and experimental validation. Mechanics of Solids, Structures, and Fluids. Vol. 9 American Society of Mechanical Engineers (ASME), 2018.
@inproceedings{5da9415f4be2413bb865ccc16290f529,
title = "Simulating eddy current sensors in blade tip timing application: Modeling and experimental validation",
abstract = "In gas turbines, the blade vibration caused by aerodynamic excitation or by self-excited vibration and flutter leads to high cycle fatigue that represents the main cause of damage in turbomachinery. Turbine operators have resorted to assess the blade vibrations using non-contact systems. One of the well-known non-contact methods is Blade Tip Timing (BTT). BTT is based on monitoring the time history of the passing of each blade tip by stationary sensors mounted in a casing around the blades. The BTT method evaluates the blade time of arrival (ToA) in order to estimate the vibration. To perform the BTT technique, optical sensors were widely used by industry due to their high accuracy and performance under high temperatures, but the main drawback of these systems is their low tolerance to the presence of contaminants. To mitigate this downside, Eddy Current Sensors (ECS) are a good alternative for health monitoring application in gas turbines due to their immunity to contaminants and debris. This type of sensor was used by many researches, predominantly on the experimental side. The focus was to extract response frequencies and therefore the accuracy of the timing measurement was ignored due to the lack of modeling. This paper fills the gap between experiments and modeling by simulating a BTT application where detailed finite element modeling of active and passive ECS outputs was performed. A test rig composed of a bladed disk with 12 blades clamped to a rotating shaft was designed and manufactured in order to validate the proposed models with experimental measurements. Finally, a comparison between these different types of sensor output is presented to show the effect of the blade tip clearance and rotational speed on the accuracy of the BTT measurement.",
author = "Nidhal Jamia and Friswell, {Michael I.} and Sami El-Borgi and Prakash Rajendran",
year = "2018",
month = "1",
day = "1",
doi = "10.1115/IMECE2018-87414",
language = "English",
volume = "9",
booktitle = "Mechanics of Solids, Structures, and Fluids",
publisher = "American Society of Mechanical Engineers (ASME)",

}

TY - GEN

T1 - Simulating eddy current sensors in blade tip timing application

T2 - Modeling and experimental validation

AU - Jamia, Nidhal

AU - Friswell, Michael I.

AU - El-Borgi, Sami

AU - Rajendran, Prakash

PY - 2018/1/1

Y1 - 2018/1/1

N2 - In gas turbines, the blade vibration caused by aerodynamic excitation or by self-excited vibration and flutter leads to high cycle fatigue that represents the main cause of damage in turbomachinery. Turbine operators have resorted to assess the blade vibrations using non-contact systems. One of the well-known non-contact methods is Blade Tip Timing (BTT). BTT is based on monitoring the time history of the passing of each blade tip by stationary sensors mounted in a casing around the blades. The BTT method evaluates the blade time of arrival (ToA) in order to estimate the vibration. To perform the BTT technique, optical sensors were widely used by industry due to their high accuracy and performance under high temperatures, but the main drawback of these systems is their low tolerance to the presence of contaminants. To mitigate this downside, Eddy Current Sensors (ECS) are a good alternative for health monitoring application in gas turbines due to their immunity to contaminants and debris. This type of sensor was used by many researches, predominantly on the experimental side. The focus was to extract response frequencies and therefore the accuracy of the timing measurement was ignored due to the lack of modeling. This paper fills the gap between experiments and modeling by simulating a BTT application where detailed finite element modeling of active and passive ECS outputs was performed. A test rig composed of a bladed disk with 12 blades clamped to a rotating shaft was designed and manufactured in order to validate the proposed models with experimental measurements. Finally, a comparison between these different types of sensor output is presented to show the effect of the blade tip clearance and rotational speed on the accuracy of the BTT measurement.

AB - In gas turbines, the blade vibration caused by aerodynamic excitation or by self-excited vibration and flutter leads to high cycle fatigue that represents the main cause of damage in turbomachinery. Turbine operators have resorted to assess the blade vibrations using non-contact systems. One of the well-known non-contact methods is Blade Tip Timing (BTT). BTT is based on monitoring the time history of the passing of each blade tip by stationary sensors mounted in a casing around the blades. The BTT method evaluates the blade time of arrival (ToA) in order to estimate the vibration. To perform the BTT technique, optical sensors were widely used by industry due to their high accuracy and performance under high temperatures, but the main drawback of these systems is their low tolerance to the presence of contaminants. To mitigate this downside, Eddy Current Sensors (ECS) are a good alternative for health monitoring application in gas turbines due to their immunity to contaminants and debris. This type of sensor was used by many researches, predominantly on the experimental side. The focus was to extract response frequencies and therefore the accuracy of the timing measurement was ignored due to the lack of modeling. This paper fills the gap between experiments and modeling by simulating a BTT application where detailed finite element modeling of active and passive ECS outputs was performed. A test rig composed of a bladed disk with 12 blades clamped to a rotating shaft was designed and manufactured in order to validate the proposed models with experimental measurements. Finally, a comparison between these different types of sensor output is presented to show the effect of the blade tip clearance and rotational speed on the accuracy of the BTT measurement.

UR - http://www.scopus.com/inward/record.url?scp=85060382815&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85060382815&partnerID=8YFLogxK

U2 - 10.1115/IMECE2018-87414

DO - 10.1115/IMECE2018-87414

M3 - Conference contribution

VL - 9

BT - Mechanics of Solids, Structures, and Fluids

PB - American Society of Mechanical Engineers (ASME)

ER -