A monolithic integrated 4 × 4 tin oxide gas sensor array with on-chip multiplexing and differential readout circuits

Bin Guo, Amine Bermak, Philip C H Chan, Gui Zhen Yan

Research output: Contribution to journalArticle

49 Citations (Scopus)

Abstract

This paper presents a monolithic 4 × 4 tin oxide gas sensor array together with on-chip multiplexing and differential read-out circuitry. A robust fabrication process focusing on the integration of the CMOS circuitry and the microelectromechanical systems (MEMS) structure is first described. The gas sensor uses a surface micro-machined micro-hotplate based structure. Platinum is selected as the material of choice for both the micro heater and the sensor's electrodes, for its good thermal stability and compatibility with the sensing film. Different post-treatments are used to modify the characteristics of the tin oxide gas sensors hence improving the sensor's selectivity of the overall sensor array. Furthermore, in contrast to the conventional voltage divider read-out technique, a novel differential read-out circuit (DRC) for tin oxide gas sensors is proposed. The DRC applies a constant current to drive the sensor and uses a unit-gain single stage amplifier (inverter) to generate a fully differential output, directly from the voltage drop across the sensor. The output of the DRC is simply proportional to the difference between the voltage on the two electrodes of the sensor but not to the transistor parameters such as mobility and threshold voltage, neither to the supply voltage. The monolithic sensor array and its pre-processing circuitry have been implemented in our in-house 5 μm process. Experimental results showed good linearity at the output of the DRC for a wide range of sensor resistance variation (over 20 MΩ). The fabricated micro-hotplate sensor array was tested for four target gases. Results show good sensitivity and interesting thermal characteristic leading to only 15.5 mW power consumption for 300 °C operating temperature.

Original languageEnglish
Pages (from-to)47-54
Number of pages8
JournalSolid-State Electronics
Volume51
Issue number1
DOIs
Publication statusPublished - Jan 2007
Externally publishedYes

Fingerprint

Sensor arrays
Tin oxides
Chemical sensors
multiplexing
Multiplexing
tin oxides
readout
chips
Networks (circuits)
sensors
Sensors
gases
Voltage dividers
electric potential
Electrodes
Electric potential
Platinum
Threshold voltage
MEMS
stannic oxide

Keywords

  • Differential read-out
  • Gas sensor array
  • Monolithic integration
  • Tin oxide

ASJC Scopus subject areas

  • Electrical and Electronic Engineering
  • Electronic, Optical and Magnetic Materials
  • Condensed Matter Physics

Cite this

A monolithic integrated 4 × 4 tin oxide gas sensor array with on-chip multiplexing and differential readout circuits. / Guo, Bin; Bermak, Amine; Chan, Philip C H; Yan, Gui Zhen.

In: Solid-State Electronics, Vol. 51, No. 1, 01.2007, p. 47-54.

Research output: Contribution to journalArticle

@article{7add16fda35b498cb1bd09b24bc1490b,
title = "A monolithic integrated 4 × 4 tin oxide gas sensor array with on-chip multiplexing and differential readout circuits",
abstract = "This paper presents a monolithic 4 × 4 tin oxide gas sensor array together with on-chip multiplexing and differential read-out circuitry. A robust fabrication process focusing on the integration of the CMOS circuitry and the microelectromechanical systems (MEMS) structure is first described. The gas sensor uses a surface micro-machined micro-hotplate based structure. Platinum is selected as the material of choice for both the micro heater and the sensor's electrodes, for its good thermal stability and compatibility with the sensing film. Different post-treatments are used to modify the characteristics of the tin oxide gas sensors hence improving the sensor's selectivity of the overall sensor array. Furthermore, in contrast to the conventional voltage divider read-out technique, a novel differential read-out circuit (DRC) for tin oxide gas sensors is proposed. The DRC applies a constant current to drive the sensor and uses a unit-gain single stage amplifier (inverter) to generate a fully differential output, directly from the voltage drop across the sensor. The output of the DRC is simply proportional to the difference between the voltage on the two electrodes of the sensor but not to the transistor parameters such as mobility and threshold voltage, neither to the supply voltage. The monolithic sensor array and its pre-processing circuitry have been implemented in our in-house 5 μm process. Experimental results showed good linearity at the output of the DRC for a wide range of sensor resistance variation (over 20 MΩ). The fabricated micro-hotplate sensor array was tested for four target gases. Results show good sensitivity and interesting thermal characteristic leading to only 15.5 mW power consumption for 300 °C operating temperature.",
keywords = "Differential read-out, Gas sensor array, Monolithic integration, Tin oxide",
author = "Bin Guo and Amine Bermak and Chan, {Philip C H} and Yan, {Gui Zhen}",
year = "2007",
month = "1",
doi = "10.1016/j.sse.2006.10.015",
language = "English",
volume = "51",
pages = "47--54",
journal = "Solid-State Electronics",
issn = "0038-1101",
publisher = "Elsevier Limited",
number = "1",

}

TY - JOUR

T1 - A monolithic integrated 4 × 4 tin oxide gas sensor array with on-chip multiplexing and differential readout circuits

AU - Guo, Bin

AU - Bermak, Amine

AU - Chan, Philip C H

AU - Yan, Gui Zhen

PY - 2007/1

Y1 - 2007/1

N2 - This paper presents a monolithic 4 × 4 tin oxide gas sensor array together with on-chip multiplexing and differential read-out circuitry. A robust fabrication process focusing on the integration of the CMOS circuitry and the microelectromechanical systems (MEMS) structure is first described. The gas sensor uses a surface micro-machined micro-hotplate based structure. Platinum is selected as the material of choice for both the micro heater and the sensor's electrodes, for its good thermal stability and compatibility with the sensing film. Different post-treatments are used to modify the characteristics of the tin oxide gas sensors hence improving the sensor's selectivity of the overall sensor array. Furthermore, in contrast to the conventional voltage divider read-out technique, a novel differential read-out circuit (DRC) for tin oxide gas sensors is proposed. The DRC applies a constant current to drive the sensor and uses a unit-gain single stage amplifier (inverter) to generate a fully differential output, directly from the voltage drop across the sensor. The output of the DRC is simply proportional to the difference between the voltage on the two electrodes of the sensor but not to the transistor parameters such as mobility and threshold voltage, neither to the supply voltage. The monolithic sensor array and its pre-processing circuitry have been implemented in our in-house 5 μm process. Experimental results showed good linearity at the output of the DRC for a wide range of sensor resistance variation (over 20 MΩ). The fabricated micro-hotplate sensor array was tested for four target gases. Results show good sensitivity and interesting thermal characteristic leading to only 15.5 mW power consumption for 300 °C operating temperature.

AB - This paper presents a monolithic 4 × 4 tin oxide gas sensor array together with on-chip multiplexing and differential read-out circuitry. A robust fabrication process focusing on the integration of the CMOS circuitry and the microelectromechanical systems (MEMS) structure is first described. The gas sensor uses a surface micro-machined micro-hotplate based structure. Platinum is selected as the material of choice for both the micro heater and the sensor's electrodes, for its good thermal stability and compatibility with the sensing film. Different post-treatments are used to modify the characteristics of the tin oxide gas sensors hence improving the sensor's selectivity of the overall sensor array. Furthermore, in contrast to the conventional voltage divider read-out technique, a novel differential read-out circuit (DRC) for tin oxide gas sensors is proposed. The DRC applies a constant current to drive the sensor and uses a unit-gain single stage amplifier (inverter) to generate a fully differential output, directly from the voltage drop across the sensor. The output of the DRC is simply proportional to the difference between the voltage on the two electrodes of the sensor but not to the transistor parameters such as mobility and threshold voltage, neither to the supply voltage. The monolithic sensor array and its pre-processing circuitry have been implemented in our in-house 5 μm process. Experimental results showed good linearity at the output of the DRC for a wide range of sensor resistance variation (over 20 MΩ). The fabricated micro-hotplate sensor array was tested for four target gases. Results show good sensitivity and interesting thermal characteristic leading to only 15.5 mW power consumption for 300 °C operating temperature.

KW - Differential read-out

KW - Gas sensor array

KW - Monolithic integration

KW - Tin oxide

UR - http://www.scopus.com/inward/record.url?scp=33846610916&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=33846610916&partnerID=8YFLogxK

U2 - 10.1016/j.sse.2006.10.015

DO - 10.1016/j.sse.2006.10.015

M3 - Article

AN - SCOPUS:33846610916

VL - 51

SP - 47

EP - 54

JO - Solid-State Electronics

JF - Solid-State Electronics

SN - 0038-1101

IS - 1

ER -